Skip to main content Skip to office menu Skip to footer
Capital IconMinnesota Legislature

Office of the Revisor of Statutes

239.75 INSPECTION OF PETROLEUM PRODUCTS.
    Subdivision 1. Inspection requirements; blending exemptions. The director shall:
    (1) take samples, free of charge, of petroleum products wherever processed, blended,
held, stored, imported, transferred, offered for sale or use, or sold in Minnesota, limiting each
sample to one-half gallon;
    (2) inspect and test petroleum product samples according to the methods of ASTM or
other valid test methods adopted by rule, to determine whether the products comply with the
specifications in section 239.761;
    (3) inspect petroleum product storage tanks to ensure that the products are free from water
and impurities;
    (4) inspect and test samples submitted to the department by a licensed distributor, making the
test results available to the distributor;
    (5) inspect the labeling, price posting, and price advertising of petroleum product dispensers
and advertising signs at businesses or locations where petroleum products are sold, offered for
sale or use, or dispensed into motor vehicles;
    (6) maintain records of all inspections and tests according to the records retention policies of
the Department of Administration;
    (7) delegate to division personnel, at the director's discretion, any or all of the responsibilities,
duties, and powers in sections 239.75 to 239.80;
    (8) publish test data and information to assist persons who use, produce, distribute, or sell
petroleum-based heating and engine fuels;
    (9) audit the records of any person responsible for the product to determine compliance with
sections 239.75 to 239.792;
    (10) after consulting with the commissioner, grant a temporary exemption from the
gasoline-ethanol blending requirements in section 239.791 if the supply of ethanol is insufficient
to produce gasoline-ethanol blends;
    (11) after consulting with the commissioner, grant a temporary exemption from the
diesel-biodiesel blending requirements in section 239.77, if the supply of biodiesel is insufficient
to produce diesel-biodiesel blends; and
    (12) adopt, as an enforcement policy for the division, reasonable margins of uncertainty for
the tests used to determine compliance with the specifications in section 239.761, the oxygen
percentages in section 239.791, and the octane requirements in section 239.792 and apply the
margins of uncertainty to only tests performed by the division, not by adding the margins to
uncertainties in tests performed by any person responsible for the product.
    Subd. 2. Petroleum sample; when not meeting specifications. When a sample does not
comply with the specifications in section 239.761, the director shall reject the noncomplying
product from which the sample was taken and employ any or all of the following actions to
prohibit sale of the noncomplying product:
(1) issue a stop sale order to a person responsible for the product;
(2) reject and mark as rejected the pumps, meters, or other dispensers from which the
noncomplying product was obtained;
(3) seal and mark as sealed the storage tanks from which the noncomplying product was
obtained;
(4) issue a citation;
(5) request that a city or county attorney draft a misdemeanor complaint;
(6) when a product fails to comply with the specifications and when use of the product does
not endanger the public health or safety or adversely affect the emissions characteristics of the
equipment in which it is used, advise the person responsible for the product that the product must
be blended with another product to bring it into compliance.
    Subd. 3.[Repealed, 1992 c 575 s 54]
    Subd. 4.[Repealed, 1992 c 575 s 54]
    Subd. 5. Product quality, responsibility. After a petroleum-based engine fuel is purchased,
transferred, or otherwise removed from a refinery or terminal, the person responsible for the
product shall:
(1) keep the product free from contamination with water and impurities;
(2) not blend the product with dissimilar petroleum products, for example, gasoline must not
be blended with diesel fuel;
(3) not blend the product with any contaminant, dye, chemical, or additive, except:
(i) agriculturally derived, denatured ethanol that complies with the specifications in this
chapter;
(ii) an antiknock additive, or an additive designed to replace tetra-ethyl lead, that is registered
by the EPA;
(iii) a dye to distinguish heating fuel from low sulfur diesel fuel; or
(iv) biodiesel fuel that complies with the specifications in this chapter; and
(4) maintain a record of the name or chemical composition of the additive, with the product
shipping manifest or bill of lading for one year after the date of the manifest or bill.
    Subd. 6. Rejected product, responsibility. When a product is rejected, the person
responsible for the product shall blend or remove the product according to the director's
instructions. If the rejected product is blended with another product to bring it into compliance,
the person responsible for the product shall provide testing and documentation, in a manner
approved by the director, to prove to the director that the blended product will comply with the
specifications in section 239.761. If the rejected product is removed, the person responsible for
the product shall provide documentation to prove to the director that the rejected product has been
removed and replaced with a product that complies with the specifications in section 239.761.
History: 1987 c 268 art 14 s 2; 1992 c 575 s 23; 1Sp2005 c 1 art 4 s 64,65; 2007 c 28 s 1

Official Publication of the State of Minnesota
Revisor of Statutes